Rectangular Ducts & Fittings

Plenum Boxes

Plenum Boxes

Plenum with round take-offs are fitted with flange frames made of sheet angles and braced by cross-wise ribbing
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat

End Caps

End Caps

The end caps stops square duct ends
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket

Rectangular Take Off

Rectangular Take Off

The Take-off fittings are provided based on branches being used. Different finishing type are being used in both sides for easy installation
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw(Can be on both side or Single sided)
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat

L-Panels

L-Panels

The L Panels are beaded in regular intervals to provide strength to for large duct size.
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners(provided separately), Gasket, C Cleat

Rectangular WYE branch

Rectangular WYE branch

The wye tees are fitted with sheet angles, and the entire fitting is braced by cross-wise ribbing. This fitting allows building the duct work with two take-offs set at any angle.
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
# The width may vary between the two take-off ports

Rectangular TEE Elbow

Rectangular TEE Elbow

T-pieces with take-off bends are fitted with flange frames made of sheet angles and braced by cross-wise ribbing
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
#Angle Available: 90°,45°,30°

Rectangular TEE fitting

Rectangular TEE fitting

The T-piece ends are fitted with sheet angles, and the entire fitting is braced by cross-wise ribbing
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat

Rectangular Tapper

Rectangular Tapper

The eccentric/concentric reducers are adapters designed for coupling two rectangular ducts of different sizes
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat

Rectangular Offsets

Rectangular Offsets

Offsets help bypassing obstacles along the duct work route, i.e. at intersections of two ducts.
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat

Rectangular Radius Elbow

Rectangular Radius Elbow

The 90˚ elbows are fitted with sheet angles, and the entire product is braced by cross-wise ribbing.
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat
#Angle Available: 90°,45°,30°

Rectangular Straigth Ducts

Rectangular Straigth Ducts

All rectangular ducts are fitted with flange frames made of sheet angles and braced by cross-wise ribbing.
#Available Materials: Galvanized, Aluminium, Stainless Steel.
#Thickness: 26 -18 gauge for Galvanized, .032 - .050 gauge for Aluminium, 24-20 gauge for Stainless Steel
#Length: 100mm-5000mm*
#Finishing type: TDF, S&D, Raw
#Inclusive: Bolt & Nuts, TDF Corners, Gasket, C Cleat

© 2021 by KR Industries.

  • LinkedIn
  • Instagram
  • Facebook Social Icon
End Caps

Go to link